Skip to content

Waco, Texas

ISO consultants for Waco aircraft modification suppliers and manufacturers.

Waco keeps old aircraft flying, and sustainment buys parts their makers stopped producing. Two DFARS clauses decide how those parts are sourced and checked, and both reach suppliers well below the prime.

ISO certification consulting in Waco at a glance

Who we are
Glocal Insight: senior ISO management system consultants working with Waco companies on site and remotely. The consultant who scopes the work does the work.
Standards
ISO 9001, AS9100, ISO 14001, ISO 45001, ISO 27001, ISO 42001, ISO 13485, ISO 17025, plus internal audits, auditor training and ISO certification maintenance.
Typical timeline
For ISO 9001 at a company of 10 to 100 people, about three to four months from kickoff to the Stage 2 audit. Week by week.
Cost
A standalone gap analysis is typically in the low five figures; full implementation depends on scope. Certification body fees are separate. How certification costs are set, or estimate your audit days.
Track record
100% certification success. 100% of surveyed clients would recommend us.
Contact
(816) 535-0738 or start a conversation.

Counterfeit controls in a sustainment town

The Waco metropolitan area is three counties: McLennan, Bosque and Falls. It has 285 manufacturing establishments, 255 of them with fewer than 100 employees — 89% of the base — employing about 12,983 people (US Census County Business Patterns, 2023). Aerospace product and parts manufacturing employs about 2,380 people here at about 5.1 times the national concentration, roughly one private manufacturing job in seven (BLS QCEW, 2024 annual averages).

L3Harris describes its Waco work as modification and sustainment. Its Texas fact sheet (July 2026) calls its Waco site one of the company’s largest aircraft modification centers: more than a million square feet of buildings, more than 75 aircraft variants delivered, C-130 modernization and sustainment, depot maintenance on the EC-130H Compass Call since 2003, the first overhauled P-8A Poseidon returned to the Navy in July 2025, and, since August 2025, the production center for the Air Force’s OA-1K Skyraider II.

Sustainment buys old parts. Aircraft kept flying for decades need electronics their makers may no longer produce, and parts that are out of production are where the easy, authorized sources run out. Defense contracts deal with that risk through two DFARS clauses: 252.246-7007, which requires a counterfeit electronic part detection and avoidance system, and 252.246-7008, which controls where electronic parts may be bought.

Both reach past the prime. Clause 7007 flows its substance to subcontracts for electronic parts or assemblies containing electronic parts, commercial products included. And the policy behind 7008 applies to contractors and subcontractors at all tiers. A Waco cable shop, harness builder or parts distributor can receive both without ever reading a defense contract.

Industry in Waco

  • L3Harris, Waco Described in its July 2026 Texas fact sheet as one of the company's largest aircraft modification centers: C-130 sustainment, EC-130H depot maintenance since 2003, P-8A overhaul, and OA-1K Skyraider II production since August 2025
  • Aerospace product and parts manufacturing 6 establishments employing about 2,380 people, about 5.1 times the national concentration (BLS QCEW, 2024)
  • Machine shops and turned-product makers 14 establishments, 13 of them machine shops, employing about 590 people, about 2.1 times the national concentration (BLS QCEW, 2024)
  • HVAC and commercial refrigeration equipment makers 3 establishments employing about 400 people, about 4.8 times the national concentration (BLS QCEW, 2024)
  • The manufacturing base 255 of 285 establishments under 100 employees (Census CBP, 2023); manufacturing at about 1.5 times its national share of private employment (BLS QCEW, 2024)

What the counterfeit-detection clause asks for

Clause 252.246-7007 lists twelve criteria an acceptable system must address. In plain terms: training; inspection and testing of electronic parts with acceptance and rejection criteria; processes to stop counterfeit parts spreading; risk-based tracking of parts from the original manufacturer to product acceptance; buying from suppliers in line with clause 7008; reporting and quarantining counterfeit and suspect parts; methods to identify suspect parts and decide quickly whether they are counterfeit; systems to detect and avoid counterfeits; flowing the requirements down; keeping up with counterfeiting trends; screening GIDEP reports; and control of obsolete electronic parts.

That last criterion is the one that matters most in a sustainment town. When a part is out of production, the easy sources are gone and the risky ones remain. The clause does not forbid buying it; it requires a system that controls how you do.

The prime’s system is reviewed as part of the government’s review of its purchasing system. Yours is reviewed by the prime, through the flow-down and whatever supplier audits its purchase order allows.

Where the parts may come from

The sourcing policy at DFARS 246.870-2 is specific. Parts that are still in production or in stock are bought from the original manufacturer, its authorized suppliers, or suppliers that buy exclusively from them.

Parts that are no longer in production and not in stock from those sources may be bought from suppliers the contractor has identified as contractor-approved, but only if the contractor approves them using established counterfeit-prevention industry standards and processes, including inspection, testing and authentication, and takes responsibility for the authenticity of what they supply. The government can review and audit those selections.

When a part comes from anywhere else, or nobody can confirm that it is new and has not been mixed with used, refurbished or returned stock, the notification, inspection, testing and authentication requirements of clause 7008 apply.

One difference between the two clauses catches small companies out. The prescription for 7007 says not to use it in contracts set aside for small business. The prescription for 7008 has no such exception, and it covers acquisitions of commercial products too. A small-business prime can still be holding the sourcing clause.

Why AS9100 is the practical frame

Neither clause names a quality management standard. But AS9100 carries explicit counterfeit-part prevention requirements, along with configuration management and first article inspection, and aircraft customers often ask for it through their purchase orders. Building the twelve DFARS criteria inside an AS9100 system puts them under the same document control, internal audit and management review as everything else, rather than in a binder nobody updates.

For a shop whose customers ask only for ISO 9001, the counterfeit controls still have to be built: approved-supplier criteria, receiving inspection and authentication, quarantine and reporting. ISO 9001’s controls on externally provided products are where they go.

Maintenance, repair and overhaul organizations are often asked for AS9110, which is specialist work outside our scope. The parts, harnesses, machined components and kits that feed a modification line are AS9100 and ISO 9001 territory, and that is where most of Waco’s small manufacturers sit.

The rest of the Waco base

Machine shops, together with turned-product and screw, nut and bolt makers, employ about 590 people in the metro at about 2.1 times the national concentration (BLS QCEW, 2024). A shop that buys metal rather than electronics will rarely see the counterfeit electronic part clauses, but the rest of an AS9100 system still applies to its aerospace work.

Our Dallas-Fort Worth page works through a prime contractor’s published supplier requirements, which reach Texas shops through their purchase orders alongside the DFARS clauses.

How we work with companies here

We work with Waco companies on site and remotely, and we put the on-site days where being in the building changes the outcome: the gap analysis walkthrough, the first internal audit cycle and the certification audits.

The most useful first meeting here is a reading exercise: the quality and counterfeit clauses on your purchase orders, which DFARS clauses they flow down, and where your electronic parts actually come from. That settles what you are held to before anyone prices a system.

The consultant who scopes the engagement does the work. No handoff to a junior implementer after the sale.

100% certification success. Every client we have taken to a Stage 2 certification audit has been certified, with no major nonconformities. 100% of surveyed clients would recommend us. Every client who answered our client satisfaction survey said they would recommend Glocal Insight.

ISO standards we help Waco companies with

This page focuses on AS9100, and we can help Waco companies with any of the standards below. If you are deciding whether to bring in outside help, start with what an ISO consultant does, how fees work and when certification is worth it.

AS9100 in Waco

The Waco metro has 6 aerospace product and parts establishments and 13 machine shops (BLS QCEW, 2024 annual averages). Aerospace employment here runs about 5.1 times its national share. AS9100 adds aerospace requirements to ISO 9001, and it reaches machine shops and processors through the purchase orders of the aerospace companies they supply; distributors use AS9120.

The focus of this page. AS9100 consultants → · Free AS9100 internal audit checklist

ISO 9001 in Waco

The Waco metro has 285 manufacturing establishments, 255 of them with fewer than 100 employees (US Census County Business Patterns, 2023), and 200 durable-goods wholesalers (BLS QCEW, 2024 annual averages). ISO 9001 is the most widely held ISO management system certification and the base that AS9100, ISO 13485 and the other sector standards build on.

ISO 9001 consultants → · Free ISO 9001:2026 gap analysis checklist · Free ISO 9001 internal audit checklist

ISO 45001 in Waco

The Waco metro has 285 manufacturing establishments (US Census County Business Patterns, 2023) and 658 construction establishments (BLS QCEW, 2024 annual averages). ISO 45001 turns a safety program into a management system, with hazard identification, worker participation and incident follow-up that a customer, general contractor or insurer can check.

ISO 45001 consultants →

ISO 14001 in Waco

The Waco metro has 36 establishments in chemical, plastics and rubber, paper, primary metal, and metal coating and finishing manufacturing (BLS QCEW, 2024 annual averages), the industries where air, water and waste obligations tend to be heaviest. ISO 14001 gives a site one system for its permits, its environmental aspects and its customers' sustainability questionnaires.

ISO 14001 consultants → · Free ISO 14001:2026 gap analysis checklist · Free ISO 14001 internal audit checklist

ISO 27001 in Waco

The Waco metro has 106 computer systems design, software publishing and hosting establishments (BLS QCEW, 2024 annual averages). ISO 27001 is the internationally recognized certification for an information security management system, and a common answer to enterprise customers' security questionnaires.

ISO 27001 consultants → · Free ISO 27001 internal audit checklist · ISO 27001 audit days calculator

ISO 42001 in Waco

The Waco metro has 53 software publishers and custom programming firms (BLS QCEW, 2024 annual averages). ISO/IEC 42001 is the management system standard for organizations that develop or use AI, and it fits alongside an existing ISO 27001 system. See which state AI laws reference it.

ISO 42001 consultants →

ISO 13485 in Waco

The Waco metro has 16 medical equipment and electromedical device manufacturing establishments (BLS QCEW, 2024 annual averages). ISO 13485 is the quality management standard for medical devices, and since February 2, 2026 the FDA's Quality Management System Regulation incorporates it by reference.

ISO 13485 consultants → · Free ISO 13485 internal audit checklist · ISO 13485 audit days calculator

ISO 17025 in Waco

The Waco metro has 5 testing laboratories (BLS QCEW, 2024 annual averages). ISO/IEC 17025 is the accreditation standard for testing and calibration laboratories, including in-house labs whose results customers or regulators rely on.

ISO 17025 consultants →

What an engagement covers

  • Purchase order and flow-down review We read the quality clauses on your orders, identify DFARS 252.246-7007 and 7008 flow-downs, and list what each requires of your system.
  • Counterfeit detection and avoidance system The twelve DFARS criteria built as working processes: supplier approval, receiving inspection, quarantine, GIDEP screening and obsolete-part control.
  • AS9100 certification The aerospace quality management system, with counterfeit prevention, configuration management and first article inspection. See AS9100.
  • Contractor-approved supplier process Documented criteria for approving sources of out-of-production parts, with the inspection, testing and authentication evidence the policy expects.
  • ISO 9001 for commercial customers Where customers ask for ISO 9001 rather than AS9100, the same discipline in the general standard. See ISO 9001.
  • Gap analysis and roadmap Two to four weeks, fixed scope and price, with a clear go or no-go before real money is committed.
  • Internal audit and training Auditor-grade internal audits and training for buyers and receiving inspectors on counterfeit risk.

Questions we get from companies in this market

We sell electronic parts to a defense contractor in Waco. Do the counterfeit clauses apply to us?

Very likely, through flow-down. DFARS 252.246-7007 requires the contractor to include the substance of the clause in subcontracts, including subcontracts for commercial products, for electronic parts or assemblies containing electronic parts. The sourcing policy behind 252.246-7008 applies to contractors and subcontractors at all tiers. Your purchase order should cite them; if it is silent and your parts go into a defense program, ask your buyer in writing.

Can we still buy obsolete parts from brokers?

Under DFARS 246.870-2, parts no longer in production and not available from the original manufacturer or its authorized channel may be bought from contractor-approved suppliers, if the contractor approves them using established counterfeit-prevention standards and processes, including inspection, testing and authentication, and takes responsibility for authenticity. Other sources trigger the notification, inspection, testing and authentication requirements of clause 252.246-7008.

Does a small-business set-aside contract avoid the counterfeit clauses?

Only one of them. DFARS 246.870-3 says not to use clause 252.246-7007 in contracts set aside for small business. It gives no such exception for 252.246-7008, the sourcing clause, which is also used for commercial product acquisitions. Read your contract for both.

Do the DFARS clauses require AS9100?

No. They name no quality management standard. AS9100 is the practical frame because it carries counterfeit-part prevention requirements of its own, and aircraft customers often require it separately through their purchase orders. ISO 9001 can carry the same controls if you build them in.

How many manufacturers are in the Waco metro?

On the federal metropolitan definition, 285 manufacturing establishments, 255 of them with fewer than 100 employees, employing about 12,983 people (US Census County Business Patterns, 2023). That definition covers McLennan, Bosque and Falls counties. Killeen-Temple, which covers Bell, Coryell and Lampasas counties, is a separate metropolitan area.

What will AS9100 certification cost?

Most of the cost is set by audit days, which depend on the number of people in your certification scope, the complexity of the work and the number of sites. Our certification cost breakdown explains how audit days are set, and the audit days calculator gives an estimate for your headcount.